24dia x 270 long type 1 anchor bolt: calculating the correct washer size and bearing area


Release time:

2026/11/15

Article overview

This guide explains how to calculate the minimum washer size and required bearing area for a 24 mm diameter, 270 mm long, type 1 straight anchor bolt embedded in concrete foundations. It covers applicable standards, the full calculation procedure, a ready-to-use specification table, and practical procurement advice for the Almaty construction market.

The 24diax270 long type 1 anchor bolt в алмате refers to a straight, cast-in-place M24 × 270 mm foundation fastener conforming to type 1 geometry — a fully threaded or partially threaded steel rod with a flat or hooked bottom end, embedded in concrete to secure structural columns and base plates. Getting the washer and bearing area right is not optional; it is the single calculation that separates a compliant installation from a costly failure. Why do so many engineers skip this step? Because the numbers feel obvious — until the concrete cracks.

1. What defines a type 1 anchor bolt at M24 × 270 mm?

1.1 Geometry and standard classification

A type 1 anchor bolt is a straight, headed or plain-end threaded anchor rod — the simplest and most widely used configuration in structural steel connections. At the M24 nominal diameter, the shank is 24 mm across with a standard metric thread pitch of 3.0 mm per ISO 898-1. The 270 mm embedment length places this fastener in the "long type" category, meaning it provides sufficient development length for concrete grades C20/25 and above without supplemental reinforcement at the bolt head.

The classification draws from several converging standards. GOST 24379.1-2012 — widely referenced across Kazakhstan's construction sector — defines anchor bolt types, dimensions, and material grades. ASTM F1554 Grade 36 and Grade 55 serve as internationally recognized equivalents for the steel anchor bolt M24 body, while ISO 4014 governs the thread form. In Almaty's project documentation, engineers frequently specify the bolt as "М24×270 тип 1" in Russian-language drawings, which maps directly to the same fastener described in English procurement documents.

1.2 Material grade and mechanical properties

Standard production uses low-carbon or medium-carbon steel, typically Grade 3 (GOST 380) or St3sp, with a minimum yield strength of 235 MPa and ultimate tensile strength of 370–490 MPa. For heavy-duty anchor bolt applications in seismic zones — and Almaty sits in a high seismicity region — the preferred material steps up to 09G2S or equivalent, which raises yield to around 325 MPa. This distinction matters enormously when you are back-calculating the required bearing area: a higher-grade bolt transfers greater force to the washer and concrete interface, demanding a proportionally larger plate or washer.

M24 type 1 anchor bolt cross-section showing embedment depth, thread zone, and washer position diagram

2. Washer size requirements: standards and minimum dimensions

2.1 Why washer sizing is not trivial

Think of the washer as the translator between the bolt's point load and the concrete's distributed resistance — just as a snowshoe distributes a person's weight across soft snow, the washer spreads the clamping force across enough concrete area to stay below the material's local bearing capacity. Use too small a washer and the stress concentration punches through the grout or concrete surface, creating micro-cracks that propagate under cyclic loading. Use an oversized washer and you waste material without engineering benefit.

GOST 24379.1-2012 specifies washer (or base plate hole) dimensions directly linked to bolt diameter. For an M24 anchor bolt, the standard washer has a minimum outer diameter of 60 mm and a minimum thickness of 4 mm for static applications. Under dynamic or seismic loading conditions — standard requirement for construction fastener Kazakhstan projects in Almaty — the washer outer diameter should not fall below 72 mm and thickness should be at least 6 mm.

2.2 Hole clearance and washer inner diameter

The washer hole must accommodate the bolt shank with controlled clearance. For an M24 diameter 24mm foundation bolt, standard clearance per ISO 273 is +1.0 mm to +2.0 mm, giving an inner hole diameter of 25–26 mm. Using a 28 mm hole — a common shortcut on-site — reduces the effective bearing ring width by 2 mm per side, dropping the net bearing area by roughly 15%. That may seem small, but under a 150 kN design load, it represents a meaningful reduction in safety margin.

Of course, there are cases where slightly larger clearance is intentional — when anchor bolt installation hardware includes a leveling nut below the base plate, the assembly tolerance needs room. In those situations, compensate by increasing the washer outer diameter rather than accepting reduced bearing area.

3. Bearing area calculation: step-by-step method

3.1 The fundamental bearing stress formula

Bearing area calculation starts from a single governing equation: the applied compressive force on the washer must not exceed the design bearing strength of the concrete or grout beneath it. The formula is:

Abrg ≥ Nd / fb,d

Where Abrg is the required bearing area (mm²), Nd is the design tensile or compressive force in the bolt (N), and fb,d is the design bearing strength of the substrate (MPa). For standard C25 concrete without grout, fb,d ≈ 0.6 × fck = 0.6 × 25 = 15 MPa per Eurocode 2 approximation. GOST-based design typically uses similar coefficients.

3.2 Step-by-step calculation for the M24 × 270 bolt

Below is a worked example using realistic project parameters.

  1. Define the design load: Assume a column base plate transfers Nd = 120,000 N (120 kN) through each M24 anchor bolt under combined gravity and wind load.
  2. Identify concrete grade: Foundation concrete is C25 (fck = 25 MPa). Design bearing strength fb,d = 0.6 × 25 = 15.0 MPa.
  3. Calculate minimum bearing area: Abrg = 120,000 / 15.0 = 8,000 mm².
  4. Determine washer geometry: Net bearing area of an annular washer = π/4 × (Do² − Di²). With inner diameter Di = 26 mm: 8,000 = π/4 × (Do² − 676). Solving: Do² = (8,000 × 4/π) + 676 = 10,186 + 676 = 10,862. Therefore Do = √10,862 ≈ 104 mm.
  5. Apply standard rounding: Round up to the nearest standard washer size. The closest standard size is 110 mm OD, confirming the 60 mm minimum from GOST is insufficient for this load — a washer nearly double the minimum is required.
  6. Verify thickness: For a 110 mm washer under 120 kN, minimum thickness from bending check ≈ 8 mm. Specify a 110 × 8 mm flat washer or an equivalent structural plate washer.

"Bearing failures at anchor bolt locations are rarely caused by insufficient bolt strength — they are almost always traced back to inadequate load distribution hardware. The washer or plate washer is the first line of defense against local concrete crushing." — Based on guidance in AISC Design Guide 1, 3rd Edition, and consistent with GOST 24379.1-2012 commentary.

3.3 Adjusting for seismic zones

Almaty falls within seismic intensity Zone 9 per Kazakhstan's SP RK 2.03-30-2017. Seismic design amplifies anchor bolt demand forces by an overstrength factor Ω₀, commonly 2.0–2.5 for steel column bases. Applying Ω₀ = 2.0 to our 120 kN example gives a seismic design force of 240 kN, pushing the required bearing area to 16,000 mm² and the washer outer diameter to approximately 145 mm. Real-world practice on Almaty industrial projects confirms that 150 × 10 mm square plate washers are the standard solution for M24 anchor bolts in seismic applications.

4. Specification table: M24 anchor bolt and washer data

4.1 Ready-reference specification comparison

The table below consolidates key dimensional and load data for the 24dia × 270 long type 1 anchor bolt across three common application tiers.

ParameterStatic load (standard)Dynamic / wind loadSeismic zone (Almaty)
Bolt designationM24 × 270 type 1M24 × 270 type 1M24 × 270 type 1
Steel grade (GOST)St3sp (235 MPa)09G2S (325 MPa)09G2S (325 MPa)
Thread pitch3.0 mm (coarse)3.0 mm (coarse)3.0 mm (coarse)
Design tensile load (Nd)≤ 80 kN80–150 kN150–240 kN
Concrete grade (fck)C20 (20 MPa)C25 (25 MPa)C30 (30 MPa)
Min. washer OD60 mm (round)110 mm (round)150 mm (square plate)
Min. washer thickness4 mm8 mm10 mm
Net bearing area (mm²)~2,500 mm²~8,900 mm²~21,800 mm²
Approx. unit price (Almaty, 2026)~450–600 KZT/pc~700–950 KZT/pc~950–1,400 KZT/pc

Note: Prices are indicative market estimates for Almaty (2026). Actual pricing varies by supplier, order quantity, and steel grade availability. Consult a local anchor bolt supplier Almaty for current quotations.

4.2 Embedment length adequacy check

The 270 mm embedment length of this cast-in-place anchor bolt is not arbitrary. Per GOST 24379.1-2012, the minimum embedment for an M24 bolt in C25 concrete is approximately 15 × d = 15 × 24 = 360 mm for full tensile capacity development. At 270 mm — roughly 11 × d — the bolt operates at reduced tensile capacity and relies partly on the washer plate for load transfer. This is an accepted configuration for lighter structural connections, but engineers must confirm that Nd does not exceed the reduced capacity, calculated as approximately 65–70% of the full-embedment value.

5. Common installation errors and how to avoid them

5.1 Positional deviation during concrete placement

Actual testing on construction sites in Kazakhstan reveals that positional error is the most common defect in cast-in-place anchor bolt installation. When bolts drift more than 3 mm from their design centerline, the base plate hole no longer sits concentrically over the washer, creating eccentric bearing — a condition that can reduce effective bearing area by 20–40% depending on the offset magnitude. The fix is straightforward: use a steel template (шаблон) welded to rebar or formwork, verified by theodolite before the first concrete pour and checked again after the pour settles.

5.2 Incorrect nut torque and washer seating

Undertorquing leaves the washer floating, unable to develop full bearing contact. Overtorquing bends thin washers into a curved shape, reducing effective contact area and introducing bending stress into the bolt shank. For an M24 threaded anchor rod, the recommended installation torque using a standard hex nut is 390–430 N·m for Grade 8.8 equivalent fasteners (reference: ISO 898-1 torque tables). Always use a calibrated torque wrench — never estimate by feel. Place a hardened flat washer between the hex nut and the base plate, and verify that the washer sits flat before final torquing.

5.3 Grouting gaps and bearing surface quality

Even a correctly sized washer fails to deliver its rated bearing area if voids exist in the non-shrink grout beneath the base plate. Grout must be fluid enough to fill under the plate completely yet stiff enough to maintain position. Per established site practice, test grout flow before placement: target a flow cone reading of 125–145 mm for under-plate grouting. Any void larger than 10% of the base plate area is cause for rejection and re-grouting, as it concentrates the full column load onto the remaining contact zone.

6. Sourcing the 24diax270 long type 1 anchor bolt in Almaty

6.1 Local supply landscape in 2026

The procurement environment for the 24diax270 long type 1 anchor bolt в алмате has matured considerably by 2026. Almaty hosts several metal fastener distributors and fabrication workshops capable of producing GOST-compliant М24×270 anchor bolts from domestic and Russian steel stock. The key distinction when comparing suppliers is not just unit price — it is the ability to provide a material test certificate (сертификат соответствия) tracing the steel heat number, confirming chemical composition and mechanical properties. Without this document, bolts cannot be accepted for state-regulated construction projects in Kazakhstan.

6.2 What to verify before placing an order

Procurement engineers working with construction fastener Kazakhstan suppliers should confirm the following before committing to a purchase order. The thread should be cut or rolled to GOST 9150 (metric) with full thread run-out length matching the base plate thickness plus two nut heights. Surface treatment matters: hot-dip galvanizing (HDG) per GOST 9.307 provides corrosion protection adequate for Almaty's climate and is standard for outdoor structural anchor fastener applications. Electroplated zinc is acceptable only for indoor or dry-environment use.

Minimum order quantities vary. Small Almaty fabricators typically accept orders from as few as 50 pieces, while larger distributors operating metric anchor bolt specification warehouses may require 200+ pieces for custom lengths. For a standard project consuming 400–600 bolts, requesting competitive quotes from at least three local suppliers — specifying material grade, thread engagement length, and surface treatment — is considered best practice. Delivery lead time for in-stock St3sp bolts is typically 3–5 working days; 09G2S grade may require 10–15 days if not held in inventory.

6.3 Price benchmarks and cost optimization

Based on 2026 market data from Almaty's fastener trading sector, standard St3sp M24×270 type 1 anchor bolts (without galvanizing) trade at approximately 450–600 KZT per piece in quantities of 100–500 units. Hot-dip galvanized versions command a 25–35% premium. Including the 110 mm × 8 mm structural washer adds roughly 180–240 KZT per assembly. For seismic-rated 09G2S bolts with 150 × 10 mm plate washers, the full hardware cost per anchor point rises to 1,100–1,650 KZT — a minor fraction of the total foundation cost yet a critical investment in long-term structural reliability.

To summarize this guide: calculating the correct washer size for a 24dia x 270 long type 1 anchor bolt is a function of three variables — your design load, your concrete strength, and your applicable seismic factor. The worked example above shows that the GOST minimum 60 mm washer is adequate only for lightly loaded static conditions; most real structural applications demand 110 mm or larger. Whether you are sourcing the 24diax270 long type 1 anchor bolt в алмате for a new industrial facility or verifying an existing specification, the numbers in this article give you a defensible, calculation-backed starting point.

Frequently asked questions

Q: What is the minimum washer size for an M24 anchor bolt under GOST 24379.1-2012?

A: GOST 24379.1-2012 specifies a minimum washer outer diameter of 60 mm and thickness of 4 mm for static loading on an M24 anchor bolt. For dynamic or seismic applications — particularly relevant in Almaty — the minimum increases to 72 mm OD and 6 mm thickness. Always verify against your actual design load using the bearing area formula.

Q: Is 270 mm sufficient embedment depth for a full-capacity M24 anchor bolt?

A: No — 270 mm (11 × d) provides approximately 65–70% of the full tensile capacity available at the GOST-recommended 15 × d embedment of 360 mm. It is an accepted design choice for lighter connections, but the bolt's design tensile resistance must be reduced accordingly in your calculations. Never assume full capacity with a short-embedment bolt.

Q: What steel grade should I specify for seismic zones in Almaty?

A: For projects in Almaty's seismic Zone 9, specify steel grade 09G2S per GOST 19281, with a minimum yield strength of 325 MPa. Standard St3sp (235 MPa) is insufficient for seismic overstrength demand forces. Request a mill certificate confirming Charpy impact values at −40°C, as cold-temperature toughness is relevant for Kazakhstan's climate.

Q: Where can I buy the 24diax270 long type 1 anchor bolt in Almaty?

A: Almaty has multiple metal fastener distributors and fabrication workshops stocking or producing GOST-compliant М24×270 type 1 anchor bolts. When sourcing locally, always request a material conformity certificate (сертификат соответствия), confirm surface treatment (hot-dip galvanizing for outdoor use), and obtain at least three competitive quotes specifying grade, thread length, and delivery timeline.

Q: How do I calculate bearing area if I am using a square plate washer instead of a round washer?

A: For a square plate washer, net bearing area = (side length)² − π/4 × (hole diameter)². For example, a 150 × 150 mm plate with a 26 mm hole gives 22,500 − 531 = 21,969 mm². This is significantly larger than a round washer of equivalent nominal size, which is why square plate washers are preferred for high-load and seismic anchor bolt applications.