SD-type self-drilling (pre-stressed) hollow
SD-type self-drilling (pre-stressed) hollow
SD-type self-drilling (pre-stressed) hollow
SD-type self-drilling (pre-stressed) hollow
SD-type self-drilling (pre-stressed) hollow
SD-type self-drilling (pre-stressed) hollow
+
  • SD-type self-drilling (pre-stressed) hollow
  • SD-type self-drilling (pre-stressed) hollow
  • SD-type self-drilling (pre-stressed) hollow
  • SD-type self-drilling (pre-stressed) hollow
  • SD-type self-drilling (pre-stressed) hollow
  • SD-type self-drilling (pre-stressed) hollow

SD-type self-drilling (pre-stressed) hollow

Primarily used for permanent system support and advanced pre-support in weak surrounding rock, such as fractured rock strata and loose soil layers.


Category:

Low-pretension expansion-shell rock bolt

Keywords:

SD-type self-drilling (pre-stressed) hollow


Service Hotline


Product Details

 

Product Structure and Features

· Hollow anchor rod body: Continuous wave-shaped thread with concave-convex profile on the surface; the inner hollow bore serves as a grouting passage.

· Base plate and nut: Used in combination to fully exert the anchor bolt’s action on rock mass.

· Coupler: Conveniently extends the anchor rod body to facilitate drilling.

· Drill bit: Drill bits adaptable to various geological conditions.

The SD-type hollow self-drilling anchor bolt adopts a series of self-drilling bits suitable for diverse geological conditions. It is mainly applied for permanent systematic support and advance pre-support in weak surrounding rock such as fractured rock strata and loose soil layers. In this technical solution, the hollow rod body acts as a drill pipe together with the drill bit to integrate drill pipe and anchor bolt, realizing the combination of drilling and grouting. It supports semi-self-drilling and full self-drilling installation. After installation, the anchor bolt generates supporting resistance relying on the deformation of surrounding rock or stratum, and it is classified as a passive support anchor bolt.

 

Anchor Bolt Type Nominal Diameter mm Lower Yield Force kN Ultimate Force kN Total Elongation at Ultimate Force
Self-drilling Hollow Anchor Bolt 25 ≥150 ≥200 ≥5%
32 ≥280 ≥360 ≥5%
38 ≥400 ≥500 ≥5%
51 ≥630 ≥800 ≥5%

 

Scope of Application

It is mainly used for permanent systematic support in weak surrounding rock such as fractured rock strata and loose soil layers, fore-piling, soil nails, tie-back anchors, micro piles, foundation anti-floating anchor bolts (piles), etc.:

· Temporary support and permanent support for structural stability of caverns or tunnels in underground works, transportation and hydraulic tunnel projects

· Slope support, etc.

 

Construction Technology and Installation Procedures

Two processes are available for drilling and grouting of SD-type self-drilling hollow grouting anchor bolts:

1. Drilling + Post-grouting Anchoring Process This process is applicable for anchor bolts mainly used for anchoring support in rock strata that are not heavily fractured. The feature is that the self-drilling anchor bolt is drilled into the stratum by water drilling / air drilling first, followed by grouting and anchoring. This process is simple with low cost.

2. Simultaneous Drilling and Grouting Anchoring Process (IBO System) The IBO system process can be adopted when self-drilling anchor bolts are used for loose sand or fractured strata where stratum consolidation by grouting is the primary method. The Tuqiang self-drilling hollow grouting anchor bolt IBO system (DODRIVE Injection-Bore Anchor System) is specially designed for loose sand and fractured rock strata. Unlike conventional hollow self-drilling anchor bolts, this system uses a simultaneous drilling-grouting connector. Cement slurry replaces water during anchor bolt drilling, so the loose rock mass and sand soil are supported by cement slurry wall protection in the drilling process. The cement slurry mixes with sand to form cement mortar to protect the anchor bolt, preventing borehole collapse and grouting difficulties during drilling.

For simultaneous drilling and grouting construction, the water-cement ratio of cement slurry shall be determined according to stratum conditions. Generally, for initial drilling, WC=0.7:1 with pressure of 0.5~1 MPa. A lower water-cement ratio shall be adopted for final grouting filling of anchor bolts, generally WC=0.5:1 with pressure of 1~2 MPa.

 

Self-drilling hollow anchor rod system with

The construction technology for self-drilling, pre-stressable hollow anchor rods is suitable for various complex geological conditions

View Details

SD-type self-drilling (pre-stressed) hollow

Primarily used for permanent system support and advanced pre-support in weak surrounding rock, such as fractured rock strata and loose soil layers.

View Details

EXC-Type Pre-anchored Removable Prestressed Hollow Grouting Anchor Rod System

The EXC-Type Shell-expanding Removable Hollow Grouting Anchor Rod is a new type of anchor rod developed by Hangzhou Tuqiang Engineering Materials Co., Ltd. for engineering scenarios requiring pre-anchoring prior to excavation.

View Details

DCP Multi-layer Corrosion-Protected

China’s first domestically pioneered multi-corrosion-protection anchor bolt system. This support system features multiple anti-corrosion barriers. It boasts simple structure, convenient construction, excellent durability and low cost, ranking among the anchor bolts with superior supporting performance in China at present.

View Details

Consult Now

Please provide your contact information, and we will contact you as soon as possible.

Submit Message
Consult Now