Sourcing M24x270 type 1 anchor bolts hot dip galvanized: key factors to check
Release time:
2026/11/10
Article overview
This guide helps Brazilian steel-structure contractors and purchasing teams specify, compare and receive M24x270 galvanized anchor bolts. It covers geometry, ASTM F1554 grades, zinc thickness, local documentation, installation limits, inspection and an RFQ checklist, with calculations you can reuse.
Table of contents
- 1. What an M24x270 type 1 anchor bolt actually is
- 2. Steel grade and mechanical data for M24 anchor bolts
- 3. Hot dip galvanizing: coating thickness, threads and service life
- 4. Sourcing in Brazil: terms, documents and logistics
- 5. Installation: embedment, edge distance and torque
- 6. Receiving inspection and quality control
- 7. RFQ checklist and bid comparison for M24x270 bolts
- 8. Frequently asked questions
Sourcing this part correctly comes down to five checks: geometry, steel grade, zinc coating, paperwork and site fit. A 24 diax270 long type 1 anchor bolt hot dip galvanized is an M24, 270 mm, L-bent cast-in steel anchor rod with zinc coating, nut and washers, fixing steel columns to concrete foundations.
Why does a part this small cause so many disputes? Because one number can be read three ways, and the zinc changes how the nut fits. According to the CBCA 2026 survey, 336 Brazilian fabricators produced about 653.7 thousand tonnes of structural steel in 2025, up 34.1% from 2020. Every one of those frames ends on anchor bolts, so a wrong order stops erection crews on site.
What an M24x270 type 1 anchor bolt actually is
It is a cast-in anchor rod, 24 mm in diameter and 270 mm long, bent into an L at the embedded end and zinc-coated by hot dip immersion. Brazilian suppliers list it as "chumbador tipo 1 24x270 galvanizado a quente" or "parafuso de ancoragem M24". The wider family is described by the term anchor bolt, but exact dimensions decide whether the part fits your drawing.
24 diax270 long type 1 anchor bolt hot dip galvanized is an L-shaped (J-style) embedded rod of 24 mm nominal diameter and 270 mm length, zinc-coated by immersion and supplied with nut and washer. Catalogs also list it as an M24 anchor bolt 270mm, an HDG anchor bolt M24, a galvanized J-bolt anchor 24mm or a 24mm x 270mm galvanized anchor rod.
Dimensions, thread and weight conversion
The table below combines standard metric values with a mass estimate calculated from a steel density of 7,850 kg/m³. Confirm every figure against the supplier drawing before release.
| Parameter | Parâmetro (PT) | Value (metric / inch) |
|---|---|---|
| Nominal diameter | Diâmetro nominal | M24 / 0.945 in |
| Coarse pitch | Passo da rosca | 3.0 mm |
| Tensile stress area | Área de tração | 353 mm² |
| Overall length | Comprimento total | 270 mm / 10.63 in |
| Typical thread length (confirm) | Comprimento roscado | about 100 mm / 3.94 in |
| Straight bar mass, 270 mm | Massa da barra | about 0.96 kg |
| Complete set with nut and 2 washers | Conjunto completo | about 1.1–1.3 kg (estimate) |
A 24 mm bar weighs about 3.55 kg per metre, so 270 mm of straight stock is roughly 0.96 kg. The hook leg, nut and washers lift a complete set to an estimated 1.1–1.3 kg. For freight planning, 1,000 sets weigh about 1.2 tonnes before packaging.

What does type 1 mean on an anchor bolt?
"Type 1" is shape-and-grade shorthand, not a universal code. In most Brazilian purchase lists it points to the L-bent cast-in version in Grade 36 steel, and many catalogs link it to the older ASTM F1554 Grade 36 designation. ASTM F1554 itself defines Grades 36, 55 and 105 and allows straight, bent and headed ends. Write the shape, grade and bend dimensions into the purchase order instead of trusting the label. Ambiguity is the enemy.
Is M24 the same as a 1-inch anchor bolt?
No. M24 measures 24.0 mm with a 3.0 mm pitch, while 1"-8 UNC measures 25.4 mm with a 3.175 mm pitch. The 1.4 mm gap looks trivial, yet the threads do not interchange, and a base plate hole drilled for one may be tight or loose for the other. Also clarify whether 270 mm means overall length, embedded length or projection. Why do so many orders go wrong here? Three people read the same number three different ways.
Steel grade and mechanical data for M24 anchor bolts
For most column bases, ASTM F1554 Grade 36 (minimum yield 248 MPa) is the default, while Grades 55 and 105 serve designs that need higher tension. Brazilian designers check the steel under ABNT NBR 8800:2024, and the rods are commonly bought as an ASTM F1554 Grade 36 anchor bolt or an equivalent grade.
Grade comparison and calculated loads
The table converts minimum specified strengths into M24 loads using the 353 mm² tensile stress area. These are material limits, not design capacities. Apply the resistance factors from NBR 8800 or your governing code.
| ASTM F1554 grade | Min. yield (MPa) | Tensile (MPa) | Min. elongation | M24 yield load (kN) | M24 ultimate load (kN) |
|---|---|---|---|---|---|
| Grade 36 | 248 | 400–550 | 23% | about 88 | about 141 |
| Grade 55 | 380 | 517–655 | 21% | about 134 | about 182 |
| Grade 105 | 724 | 861–1034 | 15% | about 256 | about 304 |
Paraphrased from the scope of ASTM F1554 (ASTM International): the standard covers anchor bolts made in three strength grades, 36, 55 and 105, intended to anchor structural supports to concrete foundations.
Note that F1554 is written in inch sizes. A metric M24 rod is usually supplied in equivalent material, so ask for a mill certificate showing the actual chemistry and tensile results for the heat, not a generic grade statement.
Is Grade 36 enough for a base plate?
Often yes. At about 88 kN yield load per M24 bolt, Grade 36 suits many portal-frame columns in light industrial sheds. Uplift-dominated cases, such as wind on large-span warehouses, may justify Grade 55. Grade 55 may only be welded with the supplementary requirement, and Grade 105 must not be heated, bent or welded. Grade 36 is more forgiving: if a template error leaves a bolt a few millimetres out of position, a cold correction may be accepted, but only with the engineer's written approval. Heating is a different matter entirely, because it can damage both the steel and the zinc.
Hot dip galvanizing: coating thickness, threads and service life
Specify a mean zinc coating of at least 50 µm on the threaded shank, verified by magnetic gauge, because the fastener standards (ISO 10684 and ASTM A153 Class C) land in that range. The 610 g/m² figure (about 86 µm) belongs to heavier non-fastener items, so do not demand it blindly on an M24 bolt.
Coating standards compared
| Standard | Applies to | Typical requirement |
|---|---|---|
| ASTM A153 Class C | Hardware fasteners over 3/8 in | about 1.25 oz/ft² (381 g/m², about 53 µm) average |
| ASTM A153 Class B-3 | Rolled or forged items ≥ 1/4 in | 2.0 oz/ft² (610 g/m², about 86 µm) |
| ISO 10684 | Galvanized fasteners ≥ 6 mm | Mean ≥ 50 µm, local ≥ 40 µm |
| ISO 1461 | Fabricated steel articles over 6 mm | Mean ≥ 85 µm, local ≥ 70 µm |
| ABNT NBR 6323 | Brazilian galvanizing of steel products | Confirm class and edition with the galvanizer |
A line such as "hot dip galvanized anchor bolt ASTM A153" or "ISO 1461 galvanized anchor bolt" is not enough. Ask which class applies to the bolt and which to the plate or nut. Fastener-specific rules also appear in ASTM F2329. Verify the thickness values against the current edition of each standard before they go into a contract.
Oversize nuts and thread fit
Zinc thickens the thread, so a galvanized M24 bolt needs a nut tapped oversize after coating, following ASTM A563 and F2329 practice or the ISO 10684 allowances. Never pair a galvanized bolt with an ordinary nut, because it will bind or strip. An anchor bolt with nut and washer galvanized should arrive as a matched set. Think of it as a key and a lock: both must be cut for the same finish. In a hand test, the nut should run the whole thread length with finger or light-wrench effort.
How long do galvanized anchor bolts last?
| ISO 9223 category | Zinc loss (µm/year) | Approx. life of a 50 µm coating |
|---|---|---|
| C3 (urban, light industrial) | 0.7–2.1 | about 24–70 years |
| C4 (industrial, moderate coastal) | 2.1–4.2 | about 12–24 years |
| C5 (marine, aggressive industrial) | 4.2–8.4 | about 6–12 years |
These are zinc-consumption periods, not warranties. Embedded portions in sound concrete corrode far more slowly; the exposed projection under the base plate is where most losses occur. Galvanizing is therefore no substitute for stainless steel in splash zones, a misconception worth correcting early on coastal projects near Santos or Itajaí.
Sourcing in Brazil: terms, documents and logistics
Buy against a bilingual specification and a document pack: mill certificate, galvanizing report and a dimensioned drawing. Ask for prices in reais (R$) with taxes itemized, so offers can be compared line by line.
Portuguese search terms and bilingual specification
Local buyers search with local words: "chumbador de ancoragem galvanizado a fogo", "parafuso de ancoragem M24", "barra de ancoragem NBR 6323" and "chumbador tipo 1 24x270 galvanizado a quente". When you contact a galvanized anchor bolt supplier in Brazil, send both language versions so the quote cannot drift. Useful terms: porca (nut), arruela (washer), rosca (thread), comprimento (length), camada de zinco (zinc layer).
ABNT, INMETRO and certificates
For galvanizing, ABNT NBR 6323 is the Brazilian reference, so ask the galvanizer for a coating-thickness report per lot. Structural design follows ABNT NBR 8800:2024 (2025 corrected version), which tightened documentation for anchors, embedment and coating checks. I know of no blanket INMETRO mark for generic anchor bolts, so ask the supplier to state in writing whether the item falls under any INMETRO rule, and rely on traceable lot certificates (EN 10204 type 3.1 style) as proof of material.
Prices in R$, lead time and import duties
Format quotes the Brazilian way: R$ 1.250,00 with a decimal comma, and dates as dd/mm/aaaa. Request unit price per set, tax lines (ICMS, IPI, PIS/COFINS), incoterm and delivery point. Market reports say anti-dumping duties on steel introduced in February 2026 raised the cost of imported steel items, which favors traceable local galvanizing. Check with your customs broker whether they apply to fasteners. Solar projects, with installed capacity cited near 77 GW in 2026 by ABSOLAR/ANEEL figures, also compete for galvanizing slots. Ask for written production, galvanizing and shipping days instead of a single vague "prazo".
Installation: embedment, edge distance and torque
Install with the hook inside the reinforcement cage, at least six bolt diameters (144 mm) from any free edge for torqued anchors, and a rigid template holding position until the concrete sets. Treat these as starting values and follow your engineer's drawing.
Step-by-step installation
- Check the drawing for projection, embedment depth, hook orientation and bolt group spacing.
- Fix the bolts in a steel or timber template (gabarito) with locknuts, so spacing cannot move during the pour.
- Wrap the threads with tape or fit caps to keep concrete and slurry off the zinc.
- Place the hook inside the rebar cage and confirm cover and edge distance.
- Pour and vibrate carefully around the bolts, avoiding impact that shifts the template.
- After curing, clean the threads, fit the leveling nut, base plate, washer and top nut, then tighten to the specified level.
Worked example: hook pullout governs
Take a 24 diax270 long type 1 anchor bolt hot dip galvanized with about 70 mm projection, leaving roughly 190 mm of embedment (hef) in C25 concrete (25 MPa). Using the ACI 318 Chapter 17 equations, which many Brazilian designers use for concrete checks, the nominal numbers are illustrative only. Steel strength of a Grade 36 bolt is 353 × 400 ≈ 141 kN. Concrete breakout is 10 × √25 × 190^1.5 ≈ 131 kN. Hook pullout is 0.9 × 25 × 108 × 24 ≈ 58 kN, using a hook extension of 4.5 bolt diameters (108 mm). The hook, not the steel, controls. The engineer must apply reduction factors, edge effects and cracking assumptions.
Common failure modes
Typical failures include steel fracture, concrete cone breakout, hook straightening and pullout, side-face blowout near edges, and splitting between closely spaced bolts. Thread stripping from mixed galvanized and ordinary nuts is a field problem, not a design one. On tightening, torque follows T = K × D × F. For a 50% yield pretension (about 44 kN) and K ≈ 0.2, that is roughly 210 N·m, though lubrication moves K between 0.15 and 0.25. Many column bases need only snug-tight nuts, so do not over-torque Grade 36.
Receiving inspection and quality control
Inspect every lot at the gate against the purchase order: dimensions, coating thickness and certificates, and send a small sample to a laboratory for tensile testing. A one-hour check costs far less than rework after the base plates are set.
Sampling plan and tests
- Dimensions: length, thread length, hook leg and bend angle with gauges and a tape; go/no-go check on the thread.
- Coating thickness: magnetic gauge following ISO 2178, several readings per piece on shank and thread.
- Visual: smooth, continuous zinc, with no bare spots, flux residue or runs clogging the thread.
- Mechanical: tensile test per ASTM F606 or A370 on one sample per heat lot.
- Fit: nut runs the full thread by hand on sampled sets.
Use a recognized sampling scheme such as ISO 2859-1 or the project quality plan. As a pragmatic starting point, I would check 3–5 pieces per lot, then widen the sample after any failure.
Red flags at the gate
Watch for electro-galvanized parts sold as hot dip (typically a thin, bright finish below 25 µm), missing heat numbers, threads re-cut after galvanizing, white rust from wet stacking, and hooks bent to a different radius. Of course, not every blemish is grounds for rejection: minor roughness or dull gray patches are usually cosmetic under ASTM A153. Measure first, then decide.
RFQ checklist and bid comparison for M24x270 bolts
Use one bilingual RFQ so every supplier prices the same part. Attach a dimensioned drawing (PDF or DWG) and ask each bidder to return it marked up with their own dimensions.
Bilingual RFQ checklist
| Item | Português | Entry to specify |
|---|---|---|
| Size and length | Tamanho e comprimento | M24 x 270 mm overall |
| Shape | Formato | Type 1, L-bent; leg and radius per drawing |
| Steel grade | Classe do aço | ASTM F1554 Grade 36 or equivalent |
| Thread length | Comprimento roscado | about 100 mm, confirmed on drawing |
| Coating | Galvanização | Hot dip, mean ≥ 50 µm, NBR 6323 / ISO 10684 |
| Hardware | Porcas e arruelas | Oversize nut and washers, galvanized, matched set |
| Documents | Documentação | Mill certificate, galvanizing report per lot |
| Commercial | Condições comerciais | R$ per set, taxes itemized, incoterm, delivery date |
A bid-leveling scenario
Consider this hypothetical scenario, built to show the method with illustrative figures, not market data. A 1,200-set order for a logistics shed draws three offers. Offer A is 8% cheaper but has no mill certificate and quotes "zincado". Offer B has certificates but ordinary nuts. Offer C includes oversize nuts, a thickness report and a dated delivery commitment. Once A's low price is adjusted for a likely rejection and a second lot, and B's for replacing nuts on site, C is the lowest real cost. Compare landed cost, not unit price.
Summary: what to lock in before you order
Fix the geometry, grade, coating and documents in writing, and define what "270 mm" means. When you order a 24 diax270 long type 1 anchor bolt hot dip galvanized, insist on the matched oversize nut, a zinc thickness report, and a hook that your engineer has checked for pullout. Do that, and the part will do its quiet job for decades.
Frequently asked questions
Q: What is the usual thread length on an M24x270 L-shaped anchor bolt?
A: Many suppliers cut about 100 mm of thread, but there is no universal value. The right length depends on plate thickness, grout, leveling nut and nut height, so confirm it on the drawing before ordering.
Q: Can electro-galvanized bolts replace hot dip galvanized anchor bolts?
A: Usually not outdoors. Electro-galvanized coatings are typically below 25 µm, far thinner than the roughly 50 µm expected from hot dip fasteners. They may suit dry indoor use if the designer approves in writing.
Q: Which standards should appear on the purchase order?
A: Name the steel grade (ASTM F1554 Grade 36 or equivalent), the coating standard (ISO 10684, ASTM A153 or NBR 6323), the nut standard, and the required certificates. Quote the class or clause, not just the standard number.
Q: Can I bend or weld a galvanized anchor bolt on site?
A: Only with engineer approval. Cold correction of Grade 36 may be accepted in small amounts. Heating or welding damages the zinc and can alter the steel, and Grade 105 must never be heated, bent or welded.