TQ-I Type Plastic Anti-Cracking Composite Fiber for Concrete
+
  • TQ-I Type Plastic Anti-Cracking Composite Fiber for Concrete

TQ-I Type Plastic Anti-Cracking Composite Fiber for Concrete

Innovative Anti-Cracking Technology for Concrete • Patented Product


Category:

DCP Multi-layer Corrosion-Protected Anchor Bolt

Keywords:

TQ-I Type Plastic Anti-Cracking Composite Fiber for Concrete


Service Hotline


Product Details

Mechanism of Action

Function Description
Crack Resistance Prevent the formation and propagation of shrinkage cracks in mortar and concrete during plastic and hardening stages, reducing crack width, length and quantity.
Toughening Effect Improve the impact toughness of mortar and concrete, increase its ultimate deformation capacity and enhance fatigue resistance.
Spalling Resistance The capillary network channels left after fiber melting at high temperature prevent spalling of mortar and concrete under high temperature.
Thermal Crack Resistance For mass concrete, the fibers improve resistance to temperature differential cracking caused by hydration heat.
Impermeability Significantly improve the impermeability of mortar and concrete against non-pressure water, and also enhance penetration resistance against pressurized water.
Erosion & Abrasion Resistance Boost resistance of mortar and concrete to scouring and abrasion by high-velocity flow, and improve mechanical wear resistance.
Water Retention Reduce bleeding and evaporation rate of internal water in mortar and concrete, and improve water retention capacity.
Freeze-Thaw Damage Resistance Help improve the freeze-thaw damage resistance of mortar and concrete.

Bottom caption: The use of Tuqiang synthetic fibers can prevent early and late shrinkage cracking of cement mortar and concrete, and improve the integrity and durability of cement mortar and concrete materials.

 

Technical Parameters

Tuqiang Plastic Anti-Cracking Synthetic Fiber TQ-I Type (ComF(p) Type)

Technical Property Material: Polypropylene Fiber
Density (g/cm³) 0.91
Diameter (μm) 15–35
Length (±1 mm) 6, 9, 12, 18
Initial Modulus of Elasticity (GPa) ≥3.5
Tensile Strength (MPa) ≥300
Elongation at Break (%) 5–35
Fiber Shape Monofilament / Bundled
Safety Non-toxic and safe
Acid and Alkali Resistance Extremely high
Aging Resistance Very high
Thermal Conductivity Very low
Safety Non-toxic and safe

 

TQ-I Type Plastic Anti-Cracking Composite Fiber for Concrete: it reduces plastic shrinkage cracking of cement mortar and concrete.

 

Scope of Application

A: Hydraulic Engineering B: Highway and Railway Pavements C: Bridge Decks D: Factory Floors E: Parking Lot Floors F: Building Plastering G: Foundation Slabs, Roof Slabs and Floor Slabs of General Industrial and Civil Buildings H: Railway Tunnel Linings, etc.

 

Construction Technology

The use of Tuqiang synthetic fibers generally does not require changing the mix proportion of the original design.

  • The typical dosage of TQ‑I fiber is 0.9 kg/m³ of concrete; the dosage can be adjusted appropriately according to specific project conditions.

  • For T‑II type: when ambient humidity>50%, the recommended dosage is 1.5 kg fiber per cubic meter of concrete.

  • When ambient humidity is 30%–50%, the recommended dosage is 2–2.5 kg fiber per cubic meter of concrete.

  • TQ‑I fiber is added directly with dry materials (sand, stone, cement, etc.) for mixing. The mixing time shall be extended by 30–60 seconds compared with concrete without fiber.

  • TQ‑II fiber is added together with dry materials (sand, stone, cement, etc.) and dry-mixed for tens of seconds first, then add water for further mixing. The mixing time is extended by about 60 seconds compared with concrete without fiber.

Self-drilling hollow anchor rod system with

The construction technology for self-drilling, pre-stressable hollow anchor rods is suitable for various complex geological conditions

View Details

SD-type self-drilling (pre-stressed) hollow

Primarily used for permanent system support and advanced pre-support in weak surrounding rock, such as fractured rock strata and loose soil layers.

View Details

EXC-Type Pre-anchored Removable Prestressed Hollow Grouting Anchor Rod System

The EXC-Type Shell-expanding Removable Hollow Grouting Anchor Rod is a new type of anchor rod developed by Hangzhou Tuqiang Engineering Materials Co., Ltd. for engineering scenarios requiring pre-anchoring prior to excavation.

View Details

DCP Multi-layer Corrosion-Protected

China’s first domestically pioneered multi-corrosion-protection anchor bolt system. This support system features multiple anti-corrosion barriers. It boasts simple structure, convenient construction, excellent durability and low cost, ranking among the anchor bolts with superior supporting performance in China at present.

View Details

Consult Now

Please provide your contact information, and we will contact you as soon as possible.

Submit Message
Consult Now