TQ-II Type Hardening Anti-Cracking Composite Fiber for Concrete
Innovative Anti-Cracking Technology for Concrete • Patented Product
Category:
DCP Multi-layer Corrosion-Protected Anchor Bolt
Keywords:
TQ-II Type Hardening Anti-Cracking Composite Fiber for Concrete
Service Hotline
Product Details
Mechanism of Action
| Function | Description |
|---|---|
| Crack Resistance | Prevent the formation and propagation of shrinkage cracks in mortar and concrete during plastic and hardening stages, reducing crack width, length and quantity. |
| Toughening Effect | Improve the impact toughness of mortar and concrete, increase its ultimate deformation capacity and enhance fatigue resistance. |
| Spalling Resistance | The capillary network channels left after fiber melting at high temperature prevent spalling of mortar and concrete under high temperature. |
| Thermal Crack Resistance | For mass concrete, the fibers improve resistance to temperature differential cracking caused by hydration heat. |
| Impermeability | Significantly improve the impermeability of mortar and concrete against non-pressure water, and also enhance penetration resistance against pressurized water. |
| Erosion & Abrasion Resistance | Boost resistance of mortar and concrete to scouring and abrasion by high-velocity flow, and improve mechanical wear resistance. |
| Water Retention | Reduce bleeding and evaporation rate of internal water in mortar and concrete, and improve water retention capacity. |
| Freeze-Thaw Damage Resistance | Help improve the freeze-thaw damage resistance of mortar and concrete. |
Bottom caption: The use of Tuqiang synthetic fibers can prevent early and late shrinkage cracking of cement mortar and concrete, and improve the integrity and durability of cement mortar and concrete materials.
Technical Parameters
Tuqiang Hardening Anti-Cracking Synthetic Fiber TQ-II Type (ComF(h) Type)
| Technical Property | Material: Polyvinyl Alcohol Fiber |
|---|---|
| Density (g/cm³) | 1.30 |
| Diameter (μm) | 15–25 |
| Length (±1 mm) | 6, 9, 12, 18 |
| Initial Modulus of Elasticity (GPa) | ≥30 |
| Tensile Strength (MPa) | ≥1200 |
| Elongation at Break (%) | 5–20 |
| Fiber Shape | Bundled Monofilament |
| Safety | Non-toxic and safe |
| Acid and Alkali Resistance | Extremely high |
TQ‑II Type Hardening Anti‑Cracking Composite Fiber for Concrete:
The reduction rate of plastic shrinkage cracking of cement mortar and concrete ≥75%; The reduction rate of hardening shrinkage cracking of cement mortar and concrete ≥90%.
Scope of Application
A: Hydraulic Engineering B: Highway and Railway Pavements C: Bridge Decks D: Factory Floors E: Parking Lot Floors F: Building Plastering G: Foundation Slabs, Roof Slabs and Floor Slabs of General Industrial and Civil Buildings H: Railway Tunnel Linings, etc.
Construction Technology
The use of Tuqiang synthetic fibers generally does not require changing the mix proportion of the original design.
-
The typical dosage of TQ‑I fiber is 0.9 kg/m³ of concrete; the dosage can be adjusted appropriately according to specific project conditions.
-
For T‑II type: when ambient humidity>50%, the recommended dosage is 1.5 kg fiber per cubic meter of concrete.
-
When ambient humidity is 30%–50%, the recommended dosage is 2–2.5 kg fiber per cubic meter of concrete.
-
TQ‑I fiber is added directly with dry materials (sand, stone, cement, etc.) for mixing. The mixing time shall be extended by 30–60 seconds compared with concrete without fiber.
-
TQ‑II fiber is added together with dry materials (sand, stone, cement, etc.) and dry-mixed for tens of seconds first, then add water for further mixing. The mixing time is extended by about 60 seconds compared with concrete without fiber.
Self-drilling hollow anchor rod system with
The construction technology for self-drilling, pre-stressable hollow anchor rods is suitable for various complex geological conditions
View DetailsSD-type self-drilling (pre-stressed) hollow
Primarily used for permanent system support and advanced pre-support in weak surrounding rock, such as fractured rock strata and loose soil layers.
View DetailsEXC-Type Pre-anchored Removable Prestressed Hollow Grouting Anchor Rod System
The EXC-Type Shell-expanding Removable Hollow Grouting Anchor Rod is a new type of anchor rod developed by Hangzhou Tuqiang Engineering Materials Co., Ltd. for engineering scenarios requiring pre-anchoring prior to excavation.
View DetailsDCP Multi-layer Corrosion-Protected
China’s first domestically pioneered multi-corrosion-protection anchor bolt system. This support system features multiple anti-corrosion barriers. It boasts simple structure, convenient construction, excellent durability and low cost, ranking among the anchor bolts with superior supporting performance in China at present.
View Details